高温泵轴承失效分析及润滑可靠性监测系统的应用

某重油催化装置油浆泵采用集中油雾润滑方式,油液监测发现轴承润滑油中的金属元素含量高,并且呈急剧增加的趋势,拆机检查发现油浆泵轴承出现了严重磨损。分析该油浆泵轴承磨损原因,提出了采用稀油润滑和油雾润滑组合方式来改善轴承润滑。同时,采用了大型炼化企业机泵群油液监测平台对关键动设备进行状态监测,有效保证了设备长周期安全运行。     

Real‐time monitoring by proton relaxometry of radical polymerization reactions of acrylamide in aqueous solution

The potential of time‐domain nuclear magnetic resonance (TD‐NMR) for the real‐time monitoring of solution radical polymerizations is demonstrated. A model system composed of a redox‐pair initiator system, acrylamide as monomer and water as solvent was investigated. A second‐generation continuous wave free precession technique was employed to measure the longitudinal relaxation time constant (T₁) of the samples throughout the polymerization reactions. This parameter was shown to be sensitive to the reactant feed free‐radical enhancement of the water molecule relaxation time, making it a good probe to monitor monomer conversion in real time in an automated, non‐destructive fashion. It was found that the T₁ value was better than the transverse relaxation time constant (T₂) for describing the evolution of the polymerization reactions, due to its greater sensitivity to paramagnetic effects. The TD‐NMR signal variation observed was linked to the formation, propagation and termination steps of the radical polymerization kinetics scheme. These first results may contribute to the application of real‐time monitoring of radical polymerization reactions employing low‐cost and robust TD‐NMR spectrometers. © 2018 Society of Chemical Industry     

Seismic life-cycle cost analysis of ageing highway bridges under chloride exposure conditions: modelling and recommendations

Chloride-induced corrosion of highway bridges constitutes a critical form of environmental deterioration and may result in significant escalation of seismic life-cycle costs due to increased fragility during earthquake events. Most of existing literature tends to adopt simplistic uniform area loss assumptions in lieu of potentially complex, yet realistic and more detrimental, pitting corrosion models for seismic vulnerability analysis. Since the degree of deterioration depends on the severity and duration of exposure, there exists a need to investigate the influence of uniform vs. pitting corrosion assumption on seismic life-cycle costs for varied chloride exposure conditions. A case-study example of a highway bridge in Central and Southeastern US reveals consideration of pitting corrosion as critical for extreme exposures compared to relatively minor settings. Subsequently this study provides recommendations to aid bridge engineers and stakeholders to balance between computational cost and accuracy of results to aid prompt decisions on rehabilitation of ageing bridges in different exposure conditions. A framework is also included to compute seismic life-cycle costs from generic measures of corrosion, independent of assumed exposure scenario. This framework is particularly helpful for seismic loss assessment of highway bridges in chloride exposure zones with periodic field measurements to estimate the extent of structural deterioration.     

Back-analysis of geotechnical parameters on PVD-improved ground in the Mekong Delta

This study presents a back-analysis of geotechnical parameters on prefabricated vertical drain improved ground at a site in the Mekong Delta. Various time?settlement behaviors that reflected different clay thicknesses and loading patterns were observed. The total surface settlement behavior at several monitoring locations was simulated using an updated exponential method that considered staged construction. The analyzed results were validated by substituting the values into a theoretical solution for radial consolidation. The estimated theoretical behaviors were comparable with the monitored behaviors. The geotechnical parameters were back-analyzed by applying the previously analyzed results to various theoretical and empirical formulas. However, the use of extensometer data that were installed at large intervals produced different values of the geotechnical properties. Furthermore, finite element analysis supported the back-analyzed total settlement behaviors and nearly disregarded the application of the geotechnical properties that were obtained using either surface or subsurface settlement data. However, settlements and excess pore pressures in the sublayers were not successfully predicted even when the geotechnical properties were adjusted. Thus, subsurface instruments that can be installed closely in thick clay deposits are required to reliably reevaluate the variations in geotechnical properties along a certain depth.     

Identifying cooperation for innovation―a comparison of data sources

ABSTRACT

The value of social network analysis is critically dependent on the comprehensive and reliable identification of actors and their relationships. We compare regional knowledge networks based on different types of data sources, namely, co-patents, co-publications, and publicly subsidized collaborative R&D projects. Moreover, by combining these three data sources, we construct a multilayer network that provides a comprehensive picture of intraregional interactions. By comparing the networks based on the data sources, we address the problems of coverage and selection bias. We observe that using only one data source leads to a severe underestimation of regional knowledge interactions, especially those of private sector firms and independent researchers.     

A Differentially Private Data Aggregation Method Based on Worker Partition and Location Obfuscation for Mobile Crowdsensing

With the popularity of sensor-rich mobile devices, mobile crowdsensing (MCS) has emerged as an effective method for data collection and processing. However, MCS platform usually need workers’ precise locations for optimal task execution and collect sensing data from workers, which raises severe concerns of privacy leakage. Trying to preserve workers’ location and sensing data from the untrusted MCS platform, a differentially private data aggregation method based on worker partition and location obfuscation (DP-DAWL method) is proposed in the paper. DP-DAWL method firstly use an improved K-means algorithm to divide workers into groups and assign different privacy budget to the group according to group size (the number of workers). Then each worker’s location is obfuscated and his/her sensing data is perturbed by adding Laplace noise before uploading to the platform. In the stage of data aggregation, DP-DAWL method adopts an improved Kalman filter algorithm to filter out the added noise (including both added noise of sensing data and the system noise in the sensing process). Through using optimal estimation of noisy aggregated sensing data, the platform can finally gain better utility of aggregated data while preserving workers’ privacy. Extensive experiments on the synthetic datasets demonstrate the effectiveness of the proposed method.     

大数据在公共卫生应急管理中的应用--以内蒙古自治区为例

在此次新冠肺炎防控中,以大数据为代表的新一代信息技术,广泛应用于疫情管控、追踪溯源、模型预测、资源调配、舆情管控等多个方面,发挥了重大作用。通过对大数据在内蒙古自治区疫情防控中的应用分析,从应用情况、存在问题及对策建议三个方面,探讨如何合理有效地利用丰富的数据资源、大数据应用技术,对完善重大疫情防控体制机制提供强有力的支撑,从而推动自治区,乃至国家公共卫生应急管理体系的健全与完善。     

美国大数据战略及对我国启示

美国当前在大数据方面全球领先。2010年奥巴马将发展大数据上升为国家战略,建立了一系列负责大数据的专门机构,发布大量相关战略性文件和法令。大数据在美国各个领域得到广泛应用,并基本成体系。当前我国大数据发展取得进步但仍存在问题,借鉴美国大数据战略的具体做法可为完善我国大数据战略提供较好的参考价值。     

Optical in-process height measurement system for process control of laser metal-wire deposition

We propose an in-process height measurement system for a weld bead and feedback control system for wire-feeding speed for high-quality laser deposition. Metal additive manufacturing, especially laser metal-wire deposition, is effective for complex shape fabrication and repair processing. However, we must control the gap between a weld bead and a feed wire in an optimal range for high-quality deposition. Conventionally, the Z-stage pitch for multi-layer deposition must be precisely adjusted by each deposition shape. In this paper, we design an in-process height measurement system that is integrated in a laser processing head, which measures the weld bead height by a line section method. We decreased the influence of the intense thermal radiation generated from a melt pool by inserting the band-pass filter of the line beam's wavelength in the imaging system and optimizing its line laser power. Consequently, our system can measure the weld bead height near the melt pool, which is 4 mm in front of it. Next we show that our proposed system can measure the weld bead height during wire-laser metal deposition with 50-μm accuracy by comparing its value to the true value. Finally, we achieved a cylinder shape deposition of 50-mm height, regardless of the Z-stage pitch and the cylinder diameter of the multi-layer deposition, by controlling the wire-feeding speed based on the measured weld bead height.     

智能化救援监控系统在煤矿安全生产中的应用

针对煤矿发生事故后传统救援监控系统无法实时对井下人员进行动态定位，导致矿井救援盲目性大、救援效率差、救援难度大等技术难题，为了进一步提高煤矿救援效率，通过技术研究，设计了一套以通信基站为核心的智能化救援监控系统，分析了该系统结构组成、工作原理，通过在担水沟煤矿井下实际应用效果来看，智能化救援监控系统对人员定位精准度达95%，实现人员动态位置三维成像，救援效率提高至80%以上，有效缩短了煤矿事故救援时间，取得了显著应用成效。